VAK Russia 2.1.14 UDC 69.001.5

CURRENT STATE AND PROSPECTS FOR THE DEVELOPMENT OF ADDITIVE MANUFACTURING Current state and prospects for the development of additive manufacturing

Published in Construction and Architecture · Volume 14, Issue 3, 2026 · ELocator: C0048 · Rubric: 2.1.14. LIFE CYCLE MANAGEMENT OF CONSTRUCTION OBJECTS (TECHNICAL SCIENCES)
DOI: https://doi.org/10.29039/2308-0191-2026-14-3-C0048 · EDN: PAAYQK
Received: 03.09.2026 Accepted: 20.09.2026 Published: 30.09.2026 Language of publication: ru-RU
Additive manufacturing, or 3D concrete printing (3DCP), has evolved over the past two decades from laboratory experiments to implemented construction projects. Technology provides reduced material consumption and waste, lower labour costs, faster construction, and greater freedom of architectural form. However, the widespread industrial adoption of ACP remains limited due to interrelated barriers that existing studies tend to address in isolation. This paper presents a systematic literature review conducted in accordance with the PRISMA guidelines. The search was carried out in the Scopus database, covering publications mainly from 2015 to 2026. The selected sources are systematised into six areas: (1) technologies and equipment, (2) materials and mix design, (3) reinforcement and structural solutions, (4) implementation practice, (5) sustainability, and (6) digitalisation and standardisation. It is established that the technology is at TRL 6-7, since individual technical solutions have proven their performance, but system-level readiness for serial application has not been achieved. Extrusion printing remains the dominant scheme; the range of printable mixes has expanded from fine-grained mortars to geopolymers and waste-based composites, while reinforcement methods provide a significant increase in load-bearing capacity. It is found that scaling barriers are systemic in nature, with economic and regulatory constraints acting as the cause of technological and social ones. Economic assessments demonstrate a consistent advantage in terms of construction time and material consumption, but remain contradictory in terms of cost, which is determined by the scale and utilisation rate of the production system. Environmental benefits are not realised automatically and depend on mix composition, structural geometry, and the implementation scenario. The need is substantiated for harmonising test methods, developing normative rules for structural design, and creating open verified databases as conditions for the transition of ACP from demonstration projects to the practice of reliable and sustainable construction.
additive construction production, 3D concrete printing, rheology, reinforcement, sustainability, standardisation, digitalisation
Funding
The study was conducted with financial support under the state assignment approved by the Ministry of Construction of Russia (No. 069-00003-26-00 dated December 22, 2025) for 2026 and the planning period of 2027 and 2028.
Text References

1. Du H., Khan M., McNally C., Ozer, E. Advancements and challenges in 3D concrete printing: an integrated insight into material formulation, structural performance and printing strategies for sustainable future // Journal of Sustainable Cement-Based Materials, vol. 15, pp. 2627-2656, 2026, doi:https://doi.org/10.1080/21650373.2026.2665408

2. Moussaa N.O., Haim M.E., Rida L. 3D concrete printing technology: Progress and prospects for sustainable construction // Materials Research Proceedings, vol. 58, pp. 62-69, 2026, doi:https://doi.org/10.21741/9781644903933-9

3. Liu D., Zhang Z., Zhang X., Chen Z. 3D printing concrete structures: State of the art, challenges, and opportunities //Construction and Building Materials, vol. 405, 2023, doi:https://doi.org/10.1016/j.conbuildmat.2023.133364 EDN: https://elibrary.ru/AOMZPF

4. Hashimoto K., Nakase K., Yoshihara R., Honda Y., Kono K. Evaluation and Investigation of Material and Mechanical Property of 3D Printed Concrete by Means of Non-Destructive Testing Methods // Lecture Notes in Civil Engineering, vol. 585 LNCE, pp. 265-275, 2025, doi:https://doi.org/10.1007/978-981-96-2810-0_20

5. Hasani A., DorafshanS., Transforming construction? Evaluation of the state of structural 3D concrete printing in research and practice // Construction and Building Materials, vol. 438, 2024, doi:https://doi.org/10.1016/j.conbuildmat.2024.137027 EDN: https://elibrary.ru/HQVQND

6. Ma G., Buswell R., Leal da Silva W.R., Wang L., Xu J., Jones S.Z. Technology readiness: A global snapshot of 3D concrete printing and the frontiers for development // Cement and Concrete Research, vol. 156, 2022, doi:https://doi.org/10.1016/j.cemconres.2022.106774 EDN: https://elibrary.ru/PXOGCN

7. Ambily P.S., Kaliyavaradhan S.K., Rajendran N. Top challenges to widespread 3D concrete printing (3DCP) adoption–A review // European Journal of Environmental and Civil Engineering, vol. 28, pp. 300-328, 2024, doi:https://doi.org/10.1080/19648189.2023.2213294 EDN: https://elibrary.ru/VSMXBN

8. Kamel K.T., Shamass R., Lin Y.-Y., Jin R. Toward Sustainable 3D Concrete Printing: A Critical Review of Waste-Derived Materials Across Binder, Geopolymer, and Aggregate Systems // Applied Sciences (Switzerland), vol. 16, 2026, doi:https://doi.org/10.3390/app16126258

9. Murali G., Wong L.S. Waste-driven construction: A state-of-the-art review on the integration of waste in 3D printed concrete in recent researches for sustainable development // Journal of Building Engineering, vol. 98, 2024, doi:https://doi.org/10.1016/j.jobe.2024.111268 EDN: https://elibrary.ru/BISEJW

10. Laura S., Rodrigo S.R., Iván, N. Advancements in low carbon emission cements for 3D printing: a state-of-the-art review // Revista Ingenieria de Construccion, vol. 39, 2024, doi:https://doi.org/10.7764/RIC.00131.21

11. Nguyen N., Javan K., Jordan A., Akbarnezhad A., Banihashemi S. Techno-economic analysis of 3D printed modular housing: Productivity, cost, and environmental assessment // Journal of Cleaner Production, vol. 539, 2026, doi:https://doi.org/10.1016/j.jclepro.2025.147461 EDN: https://elibrary.ru/QVXHWU

12. R, V., Gettu, R., Palaniappan, S., Kumar, Y. Embodied carbon, time and cost of two post-office buildings: Comparison of 3D printed concrete and conventional buildings // Journal of Building Engineering, vol. 121, 2026, doi:https://doi.org/10.1016/j.jobe.2026.115636

13. Batikha M., Jotangia R., Baaj M.Y., Mousleh I. 3D concrete printing for sustainable and economical construction: A comparative study // Automation in Construction, vol. 134, 2022, doi:https://doi.org/10.1016/j.autcon.2021.104087 EDN: https://elibrary.ru/CKQHMN

14. Ding Y., Liu Y., Yang B., Liu J., Gao P., Tomoya N., Qi H. Application of artificial intelligence technology in 3D concrete printing quality inspection and control: a state-of-the-art review // Journal of Sustainable Cement-Based Materials, vol. 15, pp. 1075-1091, 2026, doi:https://doi.org/10.1080/21650373.2025.2589418 EDN: https://elibrary.ru/KTHHMR

15. El Mesoudy M., Foulki R., Amegouz D., Motahhir S. Artificial Intelligence in 3D Concrete Printing: A Review of Applications, Integration and Future Prospects // Lecture Notes in Networks and Systems, vol. 1642 LNNS, pp. 513-523, 2026, doi:https://doi.org/10.1007/978-3-032-07915-2_41

16. Musarat M.A., Borg R.P., Wei J., Debono C.J., Khayat K. Computer Vision and Machine Learning Approaches for Defect Detection in 3D-Printed Cementitious Materials: A Systematic Review // Infrastructures, vol. 11, 2026, doi:https://doi.org/10.3390/infrastructures11050159

17. Wang L., Zhang Z., Guo Y., Xu J., Zhou Y. AI-powered 3D printed concrete technology: a new paradigm of intelligent construction integrating materials, equipment, and structures // AI in Civil Engineering, vol. 5, 2026, doi:https://doi.org/10.1007/s43503-026-00104-x

18. Mawas K., Maboudi M., Gerke M. A review on geometry and surface inspection in 3D concrete printing // Cement and Concrete Research, vol. 199, 2026, doi:https://doi.org/10.1016/j.cemconres.2025.108030 EDN: https://elibrary.ru/NRQWDB

19. Kiriparan B., SanjayanJ., Rajeev, P. Establishing standards for 3D concrete printing: Current insights and future research needs // Engineering Structures, vol. 360, 2026, doi:https://doi.org/10.1016/j.engstruct.2026.122809 EDN: https://elibrary.ru/NBLNEQ

20. Di Marco, G., Lombardi, D., Dounas, T., Agkathidis, A., A Theoretical Framework for the Standardisation and Industrialisation of 3D Concrete Printing through Decentralised Science // Proceedings of the International Conference on Education and Research in Computer Aided Architectural Design in Europe, vol. 1, pp. 555-564, 2025, doi:https://doi.org/10.52842/conf.ecaade.2025.1.555

21. Elistratkin M., Salnikova A., Alfimova N., Kozhukhova N., Pospelova E. Hollow Concrete Block Based on High-Strength Concrete as a Tool for Reducing the Carbon Footprint in Construction // Journal of Composites Science, vol. 8, 2024, doi:https://doi.org/10.3390/jcs8090358 EDN: https://elibrary.ru/PAKYON

22. Bajwa A.U.R., Samarasinghe D.A.S., Flemmer C., Bao D.W. Systematic Literature Review of the Evaluation of the Thermal Conductivity of 3D Concrete Printed Building Elements // Journal of Architectural Engineering, vol. 32, 2026, doi:https://doi.org/10.1061/JAEIED.AEENG-2169 EDN: https://elibrary.ru/VUEDZA

23. Reis R., Aroso F., Camões A., Brandão F., Figueiredo B., Cruz P.J.S. Carbonation and Chloride Attack in 3D-Printed Cementitious Materials: A Systematic Durability Review //Sci, vol. 8, 2026, doi:https://doi.org/10.3390/sci8040093 EDN: https://elibrary.ru/JUKDDB

24. Taborda-Llano I., Hoyos-Montilla A.A., Asensio E., Guerrero A.M., Tobón J.I. Influence of the construction process parameters on the mechanical performance and durability of 3D printed concrete (3DPC): A systematic review // Journal of Building Engineering, vol. 118, 2026, doi:https://doi.org/10.1016/j.jobe.2025.114965 EDN: https://elibrary.ru/BEUSRF

25. Perrot A., Jacquet Y., Amziane S. 3D Concrete Printing: Technologies, Applications and Classifications // 3D Concrete Printing: State of the Art and Applications, pp. 1-30, 2025, doi:https://doi.org/10.1002/9781394352081.ch1

26. Perrot A., Jacquet Y. 3D Concrete Printing: State of the Art and Applications // 3D Concrete Printing: State of the Art and Applications, pp. 1-244, 2025, doi:https://doi.org/10.1002/9781394352081

27. Dubey P.K., Maurya M.C. A comprehensive review of 3D printing in construction: technology, materials, and digital workflow // Innovative Infrastructure Solutions, vol. 11, 2026, doi:https://doi.org/10.1007/s41062-025-02432-w EDN: https://elibrary.ru/AKTCQQ

28. Perrot A., Jacquet Y. 3D Concrete Printing by Extrusion and Filament Deposition // 3D Concrete Printing: State of the Art and Applications, pp. 31-65, 2025, doi:https://doi.org/10.1002/9781394352081.ch2

29. Girskas G., Kligys M. 3D Concrete Printing Review: Equipment, Materials, Mix Design, and Properties // Buildings, vol. 15, 2025, doi:https://doi.org/10.3390/buildings15122049 EDN: https://elibrary.ru/QOTEQI

30. Placzek G., Schwerdtner P. A Global Snapshot of 3D-Printed Buildings: Uncovering Robotic-Oriented Fabrication Strategies // Buildings, vol. 14, 2024, doi:https://doi.org/10.3390/buildings14113410 EDN: https://elibrary.ru/QQLDKZ

31. Xiao Y., Khader N., Vandenberg A., Lowke D., Kloft H., Hack N. Injection 3D Concrete Printing (I3DCP) Combined with Vector-Based 3D Graphic Statics // RILEM Bookseries, vol. 37, pp. 43-49, 2022, doi:https://doi.org/10.1007/978-3-031-06116-5_7

32. Maurya S., Kumar V., Panda B., Dixit U.S. A comprehensive review on 3D concrete printing: extruder design, material properties and reinforcement techniques // Rapid Prototyping Journal, pp. 1-38, 2026, doi:https://doi.org/10.1108/RPJ-05-2025-0169

33. Tarhan Y., Tarhan İ.H., Şahin R. Comprehensive Review of Binder Matrices in 3D Printing Construction: Rheological Perspectives // Buildings, vol. 15, 2025, doi:https://doi.org/10.3390/buildings15010075 EDN: https://elibrary.ru/CWEQZU

34. Tushar F.H., Hasan M., Hasan K., Mawa J., Habib M. Factors affecting flowability and rheological behavior of 3D printed concrete: A comprehensive review // Construction and Building Materials, vol. 508, 2026, doi:https://doi.org/10.1016/j.conbuildmat.2026.145140 EDN: https://elibrary.ru/QQOJKH

35. Si W., Khan M., McNally C. A Comprehensive Review of Rheological Dynamics and Process Parameters in 3D Concrete Printing // Journal of Composites Science, vol. 9, 2025, doi:https://doi.org/10.3390/jcs9060299 EDN: https://elibrary.ru/RSTVUP

36. Sun T., Ren Z., Liu J., Ong D.E.L., Doh J.-H. Rheology properties and future trend of 3D printing concrete: State of the art review // Next Materials, vol. 11, 2026, doi:https://doi.org/10.1016/j.nxmate.2026.101736 EDN: https://elibrary.ru/SDUZAI

37. Garcés G., García-Alvarado R., Bunster V. Muñoz-Sanguinetti C. Additive Construction 4.0: a systematic review of 3D concrete printing for Construction 4.0 // Engineering, Construction and Architectural Management, Vol. 33, Issue 8, 2026, 6539-6568, https://doi.org/10.1108/ECAM-07-2024-0875

38. Monkman S., Wangler T., Jamhiri B., Buswell R. A data-driven review: mix design in 3D printable concrete // Materials and Structures/Materiaux et Constructions, vol. 59, 2026, doi:https://doi.org/10.1617/s11527-026-03109-1 EDN: https://elibrary.ru/EAUDHQ

39. Saeedi A.T., Collery D., O’Flaherty T. The impact of coarse aggregates on the performance of 3D-printed concrete: a comprehensive review // Journal of Sustainable Cement-Based Materials, vol. 15, pp. 1853-1882, 2026, doi:https://doi.org/10.1080/21650373.2026.2636070 EDN: https://elibrary.ru/VQVHTM

40. Uddin M.N., Sajib M.H., Arif A., Ye, J., Majumder, A., Shi, X. From mix to structure: A critical review of 3D printed fiber reinforced concrete (3DP-FRC) // Journal of Building Engineering, vol. 120, 2026, doi:https://doi.org/10.1016/j.jobe.2026.115360 EDN: https://elibrary.ru/VRQSBI

41. Dabbaghisouraki, F., Tanhadoust, A., L. Nehdi, M. Fiber reinforcement strategies in 3D concrete printing: addressing challenges and identifying research gaps // Digital Transformation in the Construction Industry: Sustainability, Resilience, and Data-Centric Engineering, pp. 639-654, 2025, doi:https://doi.org/10.1016/B978-0-443-29861-5.00032-9

42. Warsi, S.B.F., Panda, B., Biswas, P. Exploring fibre addition methods and mechanical properties of fibre-reinforced 3D printed concrete: A review // Developments in the Built Environment, vol. 16, 2023, doi:https://doi.org/10.1016/j.dibe.2023.100295 EDN: https://elibrary.ru/IGEBGV

43. Irshidat, M., Cabibihan, J.-J., Fadli, F., Al-Ramahi, S., Saadeh, M., Waste materials utilization in 3D printable concrete for sustainable construction applications: a review // Emergent Materials, vol. 8, pp. 1357-1379, 2025, doi:https://doi.org/10.1007/s42247-024-00942-4 EDN: https://elibrary.ru/LKQUZW

44. Nan, B., Qiao, Y., Leng, J., Bai, Y. Advancing Structural Reinforcement in 3D-Printed Concrete: Current Methods, Challenges, and Innovations // Materials, vol. 18, 2025, doi:https://doi.org/10.3390/ma18020252 EDN: https://elibrary.ru/GZFCLA

45. Mechtcherine, V., Buswell, R., Kloft, H., Bos, F.P., Hack, N., Wolfs, R., Sanjayan, J., Nematollahi, B., Ivaniuk, E., Neef, T. Integrating reinforcement in digital fabrication with concrete: A review and classification framework // Cement and Concrete Composites, vol. 119, 2021, doi:https://doi.org/10.1016/j.cemconcomp.2021.103964 EDN: https://elibrary.ru/KTKHJK

46. Gebhard, L., Esposito, L., Menna, C., Mata-Falcón, J., Inter-laboratory study on the influence of 3D concrete printing set-ups on the bond behaviour of various reinforcements // Cement and Concrete Composites, vol. 133, 2022, doi:https://doi.org/10.1016/j.cemconcomp.2022.104660 EDN: https://elibrary.ru/XPVKIC

47. Hdeib, R., Maatouq, R., Awawdeh, S., A Comparative Methodology for 3D Printed Concrete Structures: Technology, Performance, and Multi-Criteria Assessment // 2025 International Conference on Decision Aid Sciences and Applications, DASA 2025, pp. 1180-1185, 2025, doi:https://doi.org/10.1109/DASA68193.2025.11498902

48. Camarena, E.K.C., Cuellar, N.L.R., De La Torre Salazar, J.R., Viability of 3D printing of concrete for the constructability of social housing // Proceedings of the LACCEI international Multi-conference for Engineering, Education and Technology, vol. 2022-July, 2022, doi:https://doi.org/10.18687/LACCEI2022.1.1.58

49. Alokshiya, M., Ashraf, W., Hatzfeld, T., Guenther, E., Evaluation of gaps in life cycle sustainability assessments of 3D concrete printing: A systematic literature review and recommendations // Cleaner Environmental Systems, vol. 22, 2026, doi:https://doi.org/10.1016/j.cesys.2026.100458

50. Motalebi, A., Khondoker, M.A.H., Kabir, G., A systematic review of life cycle assessments of 3D concrete printing //Sustainable Operations and Computers, vol. 5, pp. 41-50, 2024, doi:https://doi.org/10.1016/j.susoc.2023.08.003 EDN: https://elibrary.ru/DAGSSP

51. Van Der Putten, J., Hoogeveen, M.J., Bruurs, M.J.A.M., Laagland, H.L.M., 3DCP Structures: The Roadmap to Standardization // RILEM Bookseries, vol. 37, pp. 50-55, 2022, doi:https://doi.org/10.1007/978-3-031-06116-5_8

52. Walzer, A.N., Kozlova, M., Mohite, A., Yeomans, J.S., Hall, D.M., How to scale a 3D concrete printing facility? a stochastic decision-support framework for production investment // Journal of Information Technology in Construction, vol. 31, pp. 180-200, 2026, doi:https://doi.org/10.36680/j.itcon.2026.008 EDN: https://elibrary.ru/YIKJEM

53. Tinoco, M.P., de Mendonça, É.M., Fernandez, L.I.C., Caldas, L.R., Reales, O.A.M., Toledo Filho, R.D., Life cycle assessment (LCA) and environmental sustainability of cementitious materials for 3D concrete printing: A systematic literature review // Journal of Building Engineering, vol. 52, 2022, doi:https://doi.org/10.1016/j.jobe.2022.104456 EDN: https://elibrary.ru/LGACDD

54. Kloft, H., Lowke, D., From 3D concrete printing to digital construction sites - prospects for the construction industry of tomorrow // Betonwerk und Fertigteil-Technik/Concrete Plant and Precast Technology, vol. 92, pp. 81, 2026

55. Kamra, J., Mani, A.P., Joshi, S., Sharma, M., Modeling interdependencies among sustainability barriers to 3D printing in construction via DEMATEL // Innovative Infrastructure Solutions, vol. 11, 2026, doi:https://doi.org/10.1007/s41062-026-02746-3

56. Shivendra, B.T., Sharath Chandra, S., Singh, A.K., Kumar, R., Kumar, N., Tantri, A., Naganna, S.R., A Path towards SDGs: Investigation of the Challenges in Adopting 3D Concrete Printing in India // Infrastructures, vol. 9, 2024, doi:https://doi.org/10.3390/infrastructures9090166 EDN: https://elibrary.ru/WFYHDS